We are Manufacturing products with world class quality

SVAAR Process solution Pvt. Ltd evaporation and drying technology provides the best solution at optimal cost. We offer quality AgitatedThinFilmDryerSupplier as well as other drying and heat transfer equipment and its suitable mechanical assembly for continuous preparation for concentrated materials to dry solids. SVAAR Process Solutions has excellent engineering and design capabilities with full production capabilities. ATFD is an ideal device for continuous processing from dry solids to concentrated materials. ATFD is the evaporation of water / solvents to form a dry powder or liquid for dissolution. This precisely thin film dryer makes it possible to dry items with a completely soluble recovery. With this indirect temperature dryer, creating a few moments without air contact the dryer cannot feel, the right component for heat drying. Viscose paste or liquid slurry can be processed to evaporate the scraped surface. Provides irritated thin film evaporation for a variety of applica

Evaporation is used for subtlety different purposes and with different results in each industry. In the food processing industry, food products are concentrated to increase their shelf life, reduce volume and weight, reduce storage costs, reduce transportation costs, and increase value. If the water vapor from the first effect of a multiple-effect evaporator can be introduced into the steam chest of a second effect operating at a lower boiling point, the latent heat in the water vapor can be reused. Lowering the vapor pressure of the second effect relative to the first effect lowers the boiling point of the second effect. This arrangement of reusing vapor latent heat is called multiple-effect evaporation. A multiple-effect evaporator uses the water vapor from one effect as the heating medium for the next effect, which operates at a lower boiling point. The latent heat in water vapor can also be reused by thermally or mechanically compressing the vapor to a higher pressure and temperat

Spin Flash Drying systems are in which particulate solids are dried during transport in a hot gas stream usually air or combustion gases. The simple Spin Flash Dryer system includes six basic components: the gas heater, the wet material feeder, the drying duct, the separator, exhaust fan, and a dried product collector. The wet particles are fed into the hot gas stream sometimes with special mixing devices. The stream flows up the drying tube. The gas velocity must be greater than the free fall velocity of the largest particle to be dried. The gas velocity in relation to the particle velocity is high. Thermal contact between the conveying air and the solids as mentioned above is usually very short and therefore flash dryers are most suitable for removal of external moisture (surface moisture) and are less suitable for removal of internal moisture. At the end of the drying process a dust separation arrangement is installed. It must comply with the regulations for pollution control. For

SVAAR Process Solution pvt delivers the best solutions at optimal cost in evaporation and drying technology. We offer quality Agitated Thin Film Dryer (ATFD). As well as other drying and heat transfer equipment. ATFD is a suitable mechanical assembly for continuous preparation for concentrated materials to dry solids. SVAAR Process Solutions has excellent engineering and design capabilities with full production capabilities. The Agitated Thin Film Dryer manufacturer has a cylindrical and vertical body warming coat and a rotor inside the shell with columns and pendulum cutting edges throughout the length of the dryer. Hinged sharp blades spread the wet feed item into the warm film. The feed penetrates the dryer and is applied in the same way as the thin film on the inner surface of the shell. ATFD refers to the evaporation of water / solvents to form a dry powder or liquid for disintegration. This precisely thin film dryer has made it possible to dry items with a completely soluble

  Most of the use of Caustic soda in textile industries for Mercerization process. This process is can be done for finishing purpose in textile market industry where the large volume of diluted caustic soda are a waste product of this process. The Caustic Recovery Plant is able to recover a very huge proportion weak lye into returnable concentrated caustic soda. Which can be reused in the process and reduces the production cost of the textile industry. The Caustic Recovery plant is most likely a multi effect evaporation plant that will re-concentrate the weal lye by boiling in heat exchanger. When it reaches to the evaporator then vapor is start releasing because of water evaporation which also increases its concentration. This method is continuously repeated till its desired concentration is not reached. Basically, Textile Mills involved in of cotton & they make use of caustic in mercerizing machines. This thin caustic soda solution is drained out of the mercerizing machine af